|Surpassed rugged industry standards
|All Land Pride Rotary Cutters have been designed and tested and meet rigorous voluntary testing procedures according to ISO 4254-13.
|Arrives for quick and easy set-up. Minimal time wasted setting or prepping the unit.
|Seven Year limited gearbox warranty
|Shows confidence in gearbox integrity.
|Rugged heavy built gearboxes
|Capable of handling heavy cutting applications.
|Gearbox seal protection
|Gearbox bottom seal protection for longer bearing life.
|Sliding guard for splitter gearbox
|Sliding guard offers protection and easy access for improved efficiency of splitter gearbox maintenance.
|Detachable shields on the wing gearboxes
|Provides easy maintenance access to the driveline slip clutches and yokes.
|Two piece driveline shields
|Driveline grease zerks are easier to access.
|Low hitch weight on tractor drawbar
|Ideal for smaller hp tractors by reducing the amount of weight on the drawbar.
|Narrow A-frame tongue
|Allows for a tighter turning radius.
|Adjustable park jack angle
|Park jack can be adjusted to be perpendicular to the ground.
|Adjustable driveline support
|Serves as support rest for the driveline when the cutter is unhooked from the tractor. Assist operator when attaching driveline to the tractor power take-off shaft.
|Input driveline: Cat. 6 CV
|Driveline is matched just right for tractor capacity. Constant velocity (CV) U-joint allows for 80 degree turns without doing damage to the driveline.
|Drivelines with slip-clutches: Cat. 5 intermediate Cat. 4 or Cat. 5 wings
|Driveline is sized right for the intended cutting capacity. Slip-clutches will slip under load to minimize twist damage to driveline profiles.
|Grease zerks on end caps of driveline
|Intermediate and wing driveline cross journals are easier to grease.
|High blade tip speed
|Allows clean cutting of material.
|6" Blade overlap
|Eliminates skipping during turns.
|Forged blade bar (Optional)
|Provides the critical strength needed for consistent, top performance.
|3/16" Round stump jumper (Optional)
|Standard thick stump jumper material keeps damage to a minimum.
|Smooth top design
|Reduces accumulation of debris and is easier and faster to clean.
|Tops of decks are 100% welded
|Makes center and wing decks stronger.
|Deck ArmorTM (Optional)
|Reduces deck damage from blade to deck contact without affecting cut quality.
|Replaceable 1/4" side skirt thickness
|Increased thickness reduces damage from objects thrown into the side skirts.
|Multiple center skid shoe locations
|Run two skid shoes under the hitch pivots or two skid shoes under the wing hinges.
|Beveled skid shoes on wings
|Reduces gouging the ground when turning.
|LED signal lights
|LED lights are bright, long lasting, and resist vibration, unlike incandescent lights.
|Wire harness 7-pin plug holder
|Spring hose loop mounted holder keeps wire harness plug out of the dirt and rain.
|Hinged wing sections
|Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches, and hollows can cause uneven cutting.
|1" Solid hinge rods
|Larger diameter hinge rod provides greater strength in the hinge area.
|Wing transport lock pins
|Transport lock pins hold the wings in the folded position in the event of hydraulic loss.
|Enclosed dual 1" leveling rods
|Cutter pulls equally on the rear axle while traveling over rough terrain.
|Five-bolt hubs with larger bearings, five lip hub seals, and bolted-on hub caps
|Makes the wheel assembly more durable and longer lasting. Five hub seals make it harder for water & debris to enter the hub and grease to leave the hub. Hub caps cannot be knocked off by foreign material.
|Drain holes in wheel rims
|Allows water to drain from wheels mounted on the folded-up wings. Helps prevent paint deterioration and rusting to the wheel rims.
|Replaceable individual wheel spindles
|Spindles can be replaced when damaged without replacing entire axle assembly.
|Laminated tires: Eliminates flats. Air-filled tires: Give better cushion while transporting. Foam-filled tires: Give better cushion while transporting and can't go flat.
|LP Performance HitchTM (Optional)
|One person Hook-up. Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and pivots about the tractor drawbar up to 12 degrees in both left and right directions.
|Bar-Tite hitch (Optional)
|Ideal for extreme conditions. Clamps tight to drawbar eliminating drawbar wear.
|Maintenance free tongue & axle pivots
|Self lubricating journal bearings make for less maintenance.
|Color-coded hydraulic hose handles
|Easy hose identification & sturdy handle to easily connect & disconnect from tractor.
|Hydraulic hose holders
|Tongue mounted hose holder keeps hose tips out of the dirt.
|Greasable cast steel, continuous hinges
|Cast steel hinges make a strong connection & are easy to lubricate.
|Center axle options
|HD Single suspension center axle: Spring cushion at the cylinder for cushion with least amount of moving parts. Independent suspension center axle: Offers additional suspension support per wheel axle. Walking tandem center axle: Designed for versatility over a multitude of terrains. Parallel pivot center axle: Provides unmatched ground contact for hill-like terrains.
|Wing axle option
|Independent suspension wing axles: Offers additional suspension support on each wing axle. Walking tandem wing axles: Designed for versatility over a multitude of terrains. Parallel pivot axles: Provides unmatched ground contact for hill-like terrains.
|Dual-acting fold cylinders (optional)
|Allows for a narrow transport width of 7'3" (2.21 m).
|Easily change cut height with a flip of a spacer.
|SMV Mounting Socket (Standard) SMV Sign (Accessory)
|SMV mounting socket receives most SMV signs equipped with a mounting blade for ease of attachment and removal when transporting on a truck or trailer. SMV sign is offered as an accessory when the tractor's SMV sign and mounting blade does not fit the cutter's standard SMV mounting socket.